Solar Panel Regulator MPPT Solar Charge Controller 15 Amp SRNE – Victron Energy

Solar Panel Regulator MPPT Solar Charge Controller 15 Amp SRNE – Victron Energy. Ultra-Fast Maximum Power Point Tracking (MPPT):Under rapidly changing light conditions, such as cloudy skies, a MPPT controller significantly improves energy harvesting. It can deliver up to 30% more energy than PWM charge controllers and up to 10% more than conventional MPPT controllers.Load Output:Connect all loads to the controller’s load output to prevent battery over-discharge. The controller automatically disconnects the load when the battery voltage drops below a preset level.Alternatively, select the intelligent Battery Life battery management system.The controller protects the load output against short circuits.Connect certain loads, especially inverters, directly to the battery. In these cases, connect the inverter’s remote control to the load output. You may need a special interface cable.Battery Life – Intelligent Battery Management:If a solar charge controller cannot fully recharge a battery each day, the battery may repeatedly cycle between partial charge and deep discharge. This operating condition can severely shorten the lifespan of lead-acid batteries.The Battery Life algorithm continuously monitors the battery’s state of charge. If necessary, it gradually increases the load disconnect voltage day by day, disconnecting loads earlier until enough solar energy is available to recharge the battery to nearly 100%. Once the battery reaches this level, the system adjusts the disconnect point to ensure a near-full recharge at least once per week.Features:Bluetooth smart built in enables set-up, monitoring, updating and synchronisation with a smart phone or other Bluetooth enabled device.VE. Direct allows wired data connection to a Color Control GX, other GX products, PC or other devices.Ultra-fast Maximum Power Point Tracking (MPPT) – Especially in case of a cloudy sky, when brightness is changeable, the MPPT will improve the harvesting of energy by up to 30% compared to PWM controllers.Load output will disconnect the load when the battery has been discharged to a pre-set voltage.Battery life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level until the harvested solar energy is sufficient to recharge the battery to near 100%Over-temperature protection and power de-rating when temperature is high.A BMV battery monitor can be used to communicate battery voltage & temperature to one or more SmartSolar Charge ControllersSpecification:Battery voltage (auto select): 12/24VRated charge current: 15ANominal PV power, 12V: 220WNominal PV power, 24V: 440WMax. PV short circuit current: 15AAutomatic load disconnect: YesMax. PV open circuit voltage: 75VPeak efficiency: 98%Self-consumption – load on: 12V: 19 mA 24V: 16 mASelf-consumption – load off: 12V: 10 mA 24V: 8 mACharge voltage ‘absorption’: 14,4V/28,8V (adj.)Charge voltage ‘float’: 13,8V/27,6V (adj.)Charge algorithm: multi-stage adaptiveTemperature compensation: -16mV/C resp. -32mV/CMax continuous load current: 15ALow voltage load disconnect: 11,1V/22.2V/44,4V or 11,8V/23,6V/47,2V or Battery Life algorithmLow voltage load reconnect: 13,1V/26,2V/52,4V or 14V/28V/56V or Battery Life algorithmProtection: Output short circuit/Over temperatureOperating temperature: -30 to 60C (full rated output up to 40C)Humidity: 95%, non-condensingData communication port: VE.DirectPower terminals:6mm2/AWG10Protection category: IP43 (electronic components), IP22 (connection area)Weight: 0.5kgDimensions: h100mm x w113mm x d40mmSafety: EN/IEC 62109-1, UL 1741, CSA C22.2Data stored: Battery voltage, current & temperature, as well as load output current, PV voltage & PV currentNumber of days trends data is stored: 46